Top » Catalog » Pitot Static Tester » Series 66xx » » Model 6600-NG:Wifi-enabled

Model 6600-NG:

Automated Pitot Static Tester with 3 Outputs


Static Output

Pressure function Ps1

  • range: 0.1 to 32 or 42 inHg
  • resolution: 0.001 inHg
  • accuracy: ?0.002 inHg
  • units: inHg, mbar, psi, mmHg, kpa

Altitude function

  • range: -4000 ft. to 60,000 ft.
  • resolution: 1 foot
  • accuracy: ? 2 ft. @ 0 ft.
  • ? 6 ft. @ 35,000 ft.
  • ? 12 ft. @ 50,000 ft.
  • units: feet, meters

Climb function

  • range: 0 ft/min to ?25,000 ft/min
  • resolution: 1 ft/min
  • accuracy: ?1% of rate of climb
  • units: Feet, meters, inHg, mbar, psi, kpa, mmHg

Ps2 Output Sames as for Ps1


Pitot Output

Pressure function

  • range: 0 to 30inHg (diff)
  • resolution: 0.0001 inHg
  • accuracy: ?0.003 inHg

Airspeed function

  • range: 0 to 500 knots
  • resolution: 0.1 knots
  • accuracy: ? 0.3 knots @ 50 knots
  • ? 0.16 knots @ 100 knots
  • < 0.05 knots above 500 knots

Mach function

  • range: 0.0 to 3.0 Mach
  • resolution: 0.001 Mach
  • accuracy: ?0.001 above 0.2 Mach
  • units: (Diff. or Abs.) inHg, mbar, psi, kpa, mmHg, feet, meters, knots, kmph

Dimensions & weights

  • Main unit: 22” x 14” x 9” / 38 lbs
  • Remote unit: 7” x 8” x 2” / 1.8 lb.

Environmental specs

  • Operating temp. 0?C to 50?C (Optional: -40?V to 50?C)
  • Storage temp. -25?C to 75?C
  • Humidity: 5 to 100% non-condensing

Power requirement

  • 90-260 VAC, 47-440 Hz ; 100W (200W with heaters)
  • Optional interal battery: 6-8 hours operation


  • WLAN, RS232 (USB); Encoder

Three Outputs
In addition to the Primary Static and Pitot outputs, a third output is provided. This output can be used as a secondary static, a differential static or secondary pitot. This output allows the user to create a second altitude (in feet or mtrs), a second absolute pressure (in inHg or mbar), a differential pressure for simulating AOA (in Diff. inHg or Diff mbar) or a differential pressure for generating a second airspeed (in knots or kmph) to simulate AOS. When the third output is not used, the tester operates exactly like our 2-output tester (Model 6300)


RVSM compliant
The high accuracy of the tester and NIST-traceable calibration make the tester fully RVSM-compliant and suitable for use on all RVSM-compliant aircraft

Calibration period: 1 year

Automated operation
Simply enter the target set-points for the three outputs and the unit automatically achieves the targets, ramping at the programmed rates. Control at the set-point is stable within ? 1 foot, ? 0.1 knot or ? 0.001 inHg

Programmable limits
User-programmable limits for altitude, airspeed, Mach and VSI provide protection to the aircraft.

“Jog” and “Hold” features
Set-points can be “jogged” up or down in small increments. Ramping to a set-point can be put on “hold” and controlled at the current measured value.

“Ground” feature
Brings Pitot and Static outputs to ambient “ground” pressure after completing a test.

?Profiles? feature
A profile of set-points can be downloaded from a PC, allowing the user to step through the set-points using a single key. Each profile can have up to 50 set-points and 12 profiles can be stored in the unit.

Leak checks
Leak-checks can be performed independently on any of the three outputs. The display of ?instant? leak rates provides immediate feedback to the user

Pressure & Vacuum source
Built-in high-capacity dual vacuum pumps and pressure pump provide the pressure and vacuum source for the unit.

Remote unit
The Remote unit is the operator interface for the tester. It is small and light enough to be used in the cockpit. The tester can be turned On and Off from the Remote. All valid parameters, including altitude, climb and airspeed, are clearly displayed simultaneously on a single screen on the remote.

Manual Vent
The tester includes precision metering valves to enable manual venting of the aircraft’s pitot static system, in the event of The tester includes precision metering valves to enable manual venting of the aircraft’s pitot static system, in the event of power-loss


  • Ideal tester for use with aircraft equipped with ?smart probes? that have the ability to sense AOA and/ or AOS.
  • Leak-checks and Air-data-system accuracy-checks on all RVSM aircraft including aircraft with ?smart probes?.
  • The tester can be used either in 3-output mode or 2-output mode. In 2-output mode this tester operates exactly like our Model 6300.



This product was added to our catalog on Thursday 24 January, 2019.